Messages

[170 Degree Race Thermostat1992-2006 Viper]

170 Degree Race Thermostat
1992-2006 Viper

This direct replacement 170-degree thermostat
offers an early opening rate and improved flow.

Help your engine run cooler under track conditions.
Fits all models 1992-2006. 

Unlike cheaper aftermarket thermostats
ours are precision built to not stick.

In conjunction with our radiator and fan control,
temperature reductions of 7-10 degrees is common.

DC Club Pricing $68


DC Performance/DC Parts
Dan Cragin
[email protected]
3370 S Livonia Avenue
Los Angeles, CA 90034
310-841-6996 Tel, 310-841-6496 Fax/Orders

Solid Steering Rack Mounts
1995-06 Viper

These mounts improve handling and steering response dramatically.
A must for cars that often see the track.

They are a direct replacement for rubber isolator mounts found in production Vipers.
Constructed of lightweight aluminum for strength and durability.
DC Part Club Pricing $79.95

DC Performance/DC Parts
[email protected]
3370 S Livonia Avenue
Los Angeles, CA 90034
310-841-6996 Tel, 310-841-6496 Fax/Orders

Dan,
Sorry for the delayed response.  I do have a picture of the dead pedal installed and how it's mounted.
STEP 1 
Pull back carpet from inside of left footwell and remove approx 8 inches worth.  You will have to scrape the insulation off the carpet as the insulation is glued to the carpet, by doing this you will be gaining a half an inch of more foot room in you footwell.
STEP 2
Remove this piece, be careful to keep shims in order for easy reinstallation                                  .
STEP 3
Drill 2 .25 inch holes in place as per instructions on picture.
STEP 4
locate holes in inner footwell and cut a small slit in carpet for bolts to slip through, next insert supplied bolt through Hole A.  Outside of footwell, fit slotted hole of Dead pedal assembly over bolt end and loosley tighten nut.  Next push other supplied bolt through round hole in assembly fit through carpet and push through footwell wall hole B, tighten nut on from outside. Next fully tighten nut at Hole A. Now you can adjust your pedals and adjust you dead pedal for angle/height and comfort, it is best to place dead pedal at approx .125 inches or so above height of clutch pedal.

[Front Fascia Protection Screen1992-2002 Viper GTS/RT/10]

Front Fascia Protection Screen
1992-2002 Viper GTS/RT/10

We have seen engines ruined by loss of oil due to an oil cooler damaged
by rocks or race track debris.
These screens are 100% stainless steel with a tig welded boarder
(no chicken wire here).
They mount behind the Fascia and come with a hood release hole.

Front Fascia Screen $450.00


Dan Cragin
[email protected]
DC Performance/DC Parts
3370 S Livonia Avenue
Los Angeles, CA 90034
310-841-6996 Tel, 310-841-6496 Fax/Orders

[DC Performance]

DC Performance is one of the few companies that offer Viper performance computer upgrades. We thoroughly test all of our products and computer upgrades on our Dynojet model 224 chassis dyno. This ensures that you the customer get the most performance for your money. We offer standard, forced induction and custom calibrations.

We can supply recalibrated brand new controllers, or can recalibrate the controller that is already on your vehicle. Besides our standard flashes, we can help with any custom tuning that your car may need.
DC Performance has experience working with just about every combination of parts and tuning systems that may be on your vehicle, and has the reputation for helping people make their cars run right, when other shops have given up.

*Note: all DC Performance computers and calibrations are for "Off Road Use Only"

* All calibrations require use of a 170-degree thermostat

* Base calibrations for your controller $600

1992-2002 RT/10 and GTS

Custom calibrations from your supplied dyno sheet
Air fuel optimized
Skip shift removed
Blower calibrations

2003-2006 SRT and SRT Coupe

Performance calibration
Optimized timing and fuel
Revised fan cycle
Improved mid-range power (15-25hp)

Race fuel calibration (100 unleaded)
Optimized timing and fuel
Skip shift removed
Revised fan cycle
Improved midrange power (25-40hp)

Blower/ Turbo calibrations

Custom calibrations for larger injectors

Calibrations from your supplied dyno sheets

Contact Dan or Lyle at [email protected]

DC Performance Inc./DC Parts
3370 S Livonia Ave., Los Angeles CA 90034
310-841-6996 Tel
310-841-6496 Fax/Order

Front Fascia Protection Screen
1992-2002 Viper GTS/RT/10

We have seen engines ruined by loss of oil due to an oil cooler damaged by rocks or race track debris. These screens are 100% stainless steel with a tig
welded boarder (no chicken wire here). They mount behind the Fascia and come with a hood release hole.

Front Fascia Screen $450.00

DEAD PEDAL 1992-2002 VIPER

DC Parts has released another Race Track Generated Product (RT/GP).
The lack of a "Dead Pedal" has been an ongoing complaint
about the Viper since its inception.


With the long footwell tunnel there just isn't anywhere to put your left foot. This can be a big annoyance on the street or the track.

DC Parts has released their "Billit" Dead Pedal with Metal Adjustable bracket, giving the Racers a solid platform for their foot, during competition or long drives.
Please contact Dan at [email protected] or Lyle at [email protected]

DC Parts Club Price: $189.95

DC Performance Inc./DC Parts
3370 S Livonia Ave., Los Angeles CA 90034
310-841-6996 Tel
310-841-6496 Fax/Order

NEW PRODUCT RELEASE

1992-1996 RT/10 TOE BOX ASSEMBLY

The clutch pedal bushings for the early RT/10's have always been a problem.  

The plastic bushings wear; the clutch pedal gets loose and flops around.  The car is hard to start without pushing the pedal all the way down or it won't start at all.
This new pedal assembly fixes this problem permanently.  

1. Complete replacement toe box assembly (exchange).
2. Fully bushed clutch pedal shaft.
3. No clutch pedal play.
4. More positive shifts
5. Less clutch pedal effort and travel
 
DC Parts Club Price: $449.00

DC Performance Inc./DC Parts
3370 S Livonia Ave., Los Angeles CA 90034
310-841-6996 Tel
310-841-6496 Fax/Order

Hey Viper X, Sorry for the delay, Dan had thought I ansered you and I thought Dan had. The Sills fit behind the front tires and are reduce heat in the cabin, they fit 1992-2003 Vipers Thanks again for inquireing..........Lyle

Custom Smooth Tubes
1992-2002 Vipers

These formed silicone hoses replace the production corrugated air box inlet hoses.  Here are some advantages and features of this product.

1.   Improves airflow into air box.
2.   HP gains of 5-7hp
3.   Curved design offers better fit than other smooth tubes.
4.   Silicone construction
5.   Red, Black or Blue colors.
6.   Stainless band clamps.
7.   Power gains of 15 hp with out high flow filters.

This is the biggest bang for your buck when it comes to hp.  I recommend it to all my customers.

DC Parts Club Price: $89.99

Dan Cragin
DC Performance/DC Parts
3370 S Livonia Ave
Los Angeles, CA 90034
310-841-6996 Tel
310-841-6496 Fax/Orders

 8) After dicussing this, we beleive that Kevin is correct, We would like to see a Higher Urathane Mount
on the passanger side and a Stock Mount on Drivers Side, With our Cross/Member Trans/Mount Kit.

                                    Thanks Dan, Looking forward to going to the Drags again...............Lyle

Over the years we have battled "SIDE SILL HEAT" issues in the Dodge Viper.
The exhaust system is encapsulated and creates a Tremendous amount of
Heat around your feet and side panels. The is to hot to touch and discolores
the paint.

The biggest cause of the heat comes from the "Lack of Airflow" over the exhaust system.
Our "Stainless Steel" Side Vents Dramatically Reduce Heat Issues on the Vipers.

                                Benefits and Features.

1.Reduced Cabin Heat
2.Reduced Side Sill Heat
3.No more paint damage
4.Stainless Construction
5.Includes All Hardware and Detailed Instructions
6.GREAT LOOKING

                   DC Parts Club price  $199.00

Call (310) 841-6996
Fax (310) 841-6496 (orders)

Quick Fire Sensors 1992-2002 Viper
Our O2 sensors offer improved sampling rate and quicker operation when
Cold. As a direct replacement these sensors are far superior to the Mopar
Units. Here are some advantages.

1. NO "Check Engine Light" associated with aftermarket headers.

2. Longer leads avalible for headers (No lengthening of wires).

3. Quick Fire O2 sensor heater provides quicker response.

4. Cleaner running engine.

5. Better cold drivability.

6. Heat shielding available.


This is a great replacement sensor; I recommend it to all my customers.


               Dan Cragin

  Dan,  I discssed this with "Our Dan" and he said, if you are drag racing your car, solid motor mouints tend to bind the alimunum block and distort cylinders, we normally use the mounts on road racer cars, Thanks for inquiring, let me know if you need any more information.....................Lyle

Dan, Thanks for your interest in the DC Parts transmission mount & crossmember. Tha biggest benefits are reduced drive line flex and durability. What this gives is better shifting, under power (because the driveline is not moving) and a transmission mount that will not tear (Like we see with the production unit)  the material is formulated for the ultimate resistance and compression...........................Lyle